The required profile for plasterboard partitions 3 species

The required profile for plasterboard partitions 3 species

12 October 2017



Choosing a profile for plasterboard partitions, you should take into account its quality and main characteristicsChoosing a profile for plasterboard partitions, you should take into account its quality and basic harakteristikiPereplanirovka premises in modern times does not require special skills of construction. The easiest way is to design the construction of the partition of the drywall. It is easy to install, it is possible to partition off rooms in a residential area. Partitions may be different as blind and partial. The frame is made of galvanized profiles of different sizes.


Metal profile for plasterboard partitions

Any partition made of drywall has a base "skeleton" for fastening sheets GCR. Leaves themselves quite hefty and frame for attaching them to be reliable. Profile for plasterboard partitions copes well with the load. Design gets strong enough, and perfectly aligned.

The most popular is a metal profile for drywallThe most popular is a metal profile for drywall

The profiles differ in the types and sizes, they require coupling elements that complement the design and greater reliability connect frame:

  • The guide profile is used to attach the frame to the ceiling and the floor;
  • The rack is the basis of the frame;
  • Profile of bridge connects the rack profile;
  • ceiling;
  • Corner element bill;
  • suspensions;
  • Connector sibling;
  • Duplex connector;
  • Flexible arch profile used to create the arch;
  • Cut-off for the extension.

Profiles are also enhanced and strengthened, the frame for plasterboard to perform better from reinforced profiles. It is worth paying attention to the quality of the material.

Galvanized profile must not be damaged and rust traces, will best profile with a zinc content greater than 99%, it is less likely corrode. Factory marriage often mask painting profiles, should understand that the hidden factory marriage is dangerous, the partition can simply be destroyed.


What are the profiles required for plasterboard partitions

Each species has its purpose in the assembly. For each design uses a certain set of metal profiles and connecting elements to them. For suturing walls and ceilings using planar - they do not have stiffeners so bad withstand heavy load. To design the different arcs used arched flexible profiles. With their help it is easy to make an arch of any form, and for interior walls - wall or partition profile, they have special reinforcement ribs in the form of two convex grooves along the entire length.

Before selecting profiles for plasterboard better acquainted with professional adviceBefore selecting profiles for plasterboard better acquainted with professional advice

To make a partition, it is important to know which profiles need for plasterboard partitions:



  • The guide profile septum (UW) is used to specify the direction of the partition;
  • Rack carrier profile for partitions (CW) used to create the frame walls and secured to the guide profiles;
  • For rigidity structure between the carrier profiles mounted transverse profile of bridge linking the entire framework.

The construction market has a huge range of profiles at various prices, but it is important to remember the proper quality, frame profiles must withstand the load position.

The profiles need to take the same size for the bulk of partitions is more widely used for partial or curly possible to use the standard profile 50 mm wide.

Galvanized profile for plasterboard partitions: Dimensions

Different frameworks, use different size profiles. It is important to know what is this or that profile to the maximum quality to perform partition.

profile size depends on the characteristics of both areas, and gypsum boardprofile size depends on the characteristics of both areas, and gypsum board

Profile for plasterboard partitions - Dimensions:

  • The guide profile has a width of 28 mm, height 27 mm, length of 3 or 4 m, wall thickness 0.5 - 0.6 mm;
  • The carrier has a width of from 42 mm to 150 mm, a height of shelves 27 mm - 40 mm, 3 or 4 meters long.

More resistant to shock and impact partition profiles with greater width. It is important not to forget to make holes for the technical laying of internal communications.

Some types of profiles are pre-drilled with rubberized edges to prevent damage to the sharp edges of the wiring laid inside the walls of plasterboard.

Recommendations which profile to use for interior partitions

Interior walls of plasterboard must meet in addition to separating more and soundproofing. This can be achieved using a packing inside the wall noise insulating material.

you must purchase a special noise insulation material for filling the inner walls for good insulationyou must purchase a special noise insulation material for filling the inner walls for good insulation


For different rooms require different thickness of the wall and it depends on which profile to use for the partition:

  • To achieve the partition thickness of 7.5 cm using 50 mm wide profile;
  • Dividing wall thickness of 10 cm out of a profile with a width of 75 mm;
  • septum thickness 12.5 cm out using profile 100 mm wide.

It should be noted that the most weak and shaky partition is using profiles 50 mm wide, such a partition to perform better as a partial or decorative interior part.

The optimal width for the wall, damming space of the room, is a profile of 75 mm. Most solid wall respectively is design with a profile 100 mm wide. Increase the rigidity of thinner walls can be by addition of one profile to another, or a double layer of drywall.

frame walls made of plasterboard with their hands

Plasterboard partitions is fairly simple to install and requires no special skills. The main task is the selection of suitable profiles, and prepare them for installation.

Install plasterboard wall can independently, the main thing - to prepare in advance all the necessary materials for repairInstall plasterboard wall can independently, the main thing - to prepare in advance all the necessary materials for repair


frame walls made of plasterboard with their hands is performed in stages:

  • Fasten the rails on the floor and the ceiling of the entire length of the partition;
  • Insert and secure the rack to the guide profiles;
  • Secure longitudinal webs in each step rack profiles;
  • Close frame sheets GCR and perform finishing.

Before starting the installation of partitions, it is necessary to partition the floor and ceiling, measured off the required distance from the perpendicular to the wall at two points and then connect with a cord.

The same is done on the ceiling. Next on the guide profile attached soundproof tape. Install guides you need to use screws or dowels. Rack profiles inserted in the first guiding interior and then to the ceiling and are aligned with the level, are fixed with screws from above and below.

Sometimes the frame is performed without cross bridges, but still it is desirable to make them in order to have the sheets GCR would like more space to the frame mounting. It will give additional strength to the structure. After plating one side of the frame with plasterboard, it is necessary to lay inside the communication and then an insulating material. Necessary to fasten sheets of drywall around the edge profiles directly to Racks screws and without fanaticism utaplivaja cap slightly below the face sheet.

Types of profiles for plasterboard partitions (video)

Frame profiles for partitions securely fastened to the floor and the ceiling, turns perfectly flat surface. The doorway has the same width along the entire perimeter which facilitates the installation of doors. Partitioning options further finishing drywall great variety so this wall is not inferior to the walls of brick.

Комментарии

Leave a Reply

Your email address will not be published. Required fields are marked *

− 3 = 1

map