Is it possible to fix the drywall to wooden bars: 7 secrets of good attachment

Is it possible to fix the drywall to wooden bars: 7 secrets of good attachment

12 October 2017



Sheathe plasterboard walls can manner frameless compound or with the support frameSheathe plasterboard walls can manner frameless compound or with reference karkasaSegodnya any design ideas can be implemented by such a simple and popular material such as plasterboard. He is now used everywhere: with the help of his erect interior walls, trim window slopes, sheathe the walls inside and outside, the ceiling trim, is also popular interior decoration of the room. There are several ways plasterboard cladding: frameless compound and the use of the support frame. The most commonly applied to wooden surfaces of the second method, as the carcass material selected tree.


How to sheathe the walls of plasterboard in a wooden house with their hands

To plasterboard paneling did not bring problems and pleasing to the eye for a long time, before starting work should take into account a number of very important points.

Features wooden frame:

  1. First of all, you need to know that if you decide to carry out installation of drywall on a skeleton of wooden bars, you need to pay attention to the characteristics of the premises in which the work will be carried out. Remember that moisture adversely affects the skeleton, made of wooden slats.
  2. Carefully inspect the joists before buying: they must be free of cracks, chips and other damage.
  3. The tree from which the rails and rail, must comply with fire safety standards.
  4. Before the work it is necessary to impregnate the wood antiseptic composition: it will increase its service life. It can be anything, but usually it is recommended to use sodium fluoride.

Before sheathe the walls of plasterboard in a wooden house, saturate the walls with antiseptic compositionBefore sheathe the walls of plasterboard in a wooden house, saturate the walls with antiseptic composition

The tree - an environmentally friendly material with which to work with.

Mount plasterboard on wooden slats: the pros solutions

Despite the fact that many builders prefer the metal as a basis for drywall constructions, the tree also has its obvious advantages, which are made of a wooden frame worthy competitor metal counterparts!


The advantages of a wooden frame in front of the metal:

  • Material availability and low cost.
  • The high speed of construction.
  • Environmentally friendly.
  • Easy to operate.

Mount plasterboard possible on wooden slats - it's easy and affordableMount plasterboard possible on wooden slats - it's easy and affordable

Before you start working with wood slats will need to leave a few days indoors, where the installation for acclimatization will be carried out.

Decorating the walls of a wooden house with plasterboard: Getting Started

In any construction business can not do without special tools. To work flowed smoothly advance purchase everything you need. What is needed in dealing with plasterboard, are listed below.



Instruments:

  1. Drill or screwdriver;
  2. Hacksaw or jigsaw;
  3. Roulette;
  4. Marker or indelible pencil.

Before you begin decorating the walls, it is necessary to prepare the necessary materials and toolsBefore you begin decorating the walls, it is necessary to prepare the necessary materials and tools

materials:

  • Wooden slats and bars;
  • Self-tapping screws, wood screws;
  • Metal corners.

Any finishing work starting primarily with the cleaning of the surfaces.

The first thing you want to remove from the walls of the old coating, the remnants of insulation and sound insulation - in short, any items that may interfere with the working process.

Before operating the walls must be covered with a special primer to prevent the appearance of mold and mildew.

How to sheathe the wooden house from the inside plasterboard: do frame

When the walls are ready for use, you can proceed directly to the installation of the framework of wooden beams.

Remember that the rail must be pre-processed antiseptic which prevent decomposition and degradation of the material.

A few tips before work:


  1. The distance between the bars should be 40-60 cm.
  2. The width of the strips themselves to be of the order of 3-5 cm, but it should be borne in mind that the joints between plasterboard sheets of a thickness shall not be less than 8 cm.
  3. Mounting rails better to do directly to the wooden wall and to each other. For this purpose, screws are ideal.

Sheathe the wooden house from the inside, you can use the framework of wooden beamsSheathe the wooden house from the inside, you can use the framework of wooden beams

Frame assembly itself should begin by securing continuous beams along the walls and ceiling. Thereafter possible to start mounting rails that are arranged vertically. Further anchoring between the vertical bars additional horizontal slats short jumper. Between a carcass part can fasten building corners and lining, it will give it added stability.

When carrying out vertical and horizontal rails it is necessary to establish strictly on level!

After that, if necessary you will need to align the frame relative to a wooden wall. This is done as follows: in the right places is enclosed bars of the desired thickness. After the installation is finished the frame, you can start attaching sheets of drywall to get the rails and beams.

The walls are made of plasterboard in a wooden house: preparing material

Before you start to mount drywall sheets on a skeleton, they need to be cut. When cutting drywall, be careful and accurate, use quality tools that will ensure your safety.


For cutting sheets of drywall will need:

  • Long rake or long level;
  • Pencil or marker;
  • A sharp knife;
  • Roulette.

The first step is metered the desired length and width of the gypsum board. Next, a knife cuts through the first layer of paper and a plaster base nadlamyvayutsya sheet of slit lines. Then penetrate the paper sheet, on the other hand, bending it at an angle 90®, and uneven ends zashlifovyvayut sandpaper or a file.

Before fastening the drywall sheets to be cutBefore fastening the drywall sheets to be cut

In the calculations of the sheet dimensions must take into account that you will place them with an offset.

Before installation, you may be faced with an issue like cutouts. They may be on the edge and in the middle of the sheet. If the cutout is located at the edge, a hacksaw or jigsaw must penetrate the two parallel lines in the opposite direction from the edge of a sheet of drywall and fracture. To make the cut in the middle of the sheet, it is necessary to saw the three lines and fracture.

How to align the wall with plasterboard in a wooden house: installation of gypsum boards to the frame

After preparing the drywall can proceed directly to its attachment to the crate. To do this, we come to putting a sheet of rails and fasten them with the screws. One edge of the paper should be positioned as close as possible to the wall. Bits screws must be below the level of the sheet.

Important points:

  • Screws and screws for wood should be: they are better fixed in the wood.
  • The edges of the sheets of drywall should be in the middle of the struts.
  • If necessary, use an intermediate profile.

Align the wall in a wooden house, you can use the framework to which will be attached to the drywall sheetsAlign the wall in a wooden house, you can use the framework to which will be attached to the drywall sheets

By implementing the alignment of walls follow distance between screws: it should not exceed 25-30 cm.

Processing wall or plasterboard partitions in a wooden house

After the installation is completed, the connection between the sheets of plasterboard, and the holes of the screws should be treated with hats.

To do this we need to:

  • Putty knife;
  • Special putty;
  • Reinforced tape or mesh;
  • Electric drill with paddle for mixing filler.

To process the walls or partitions in the house will need putty, reinforced tape, electric drill and a trowelTo process the walls or partitions in the house will need putty, reinforced tape, electric drill and a trowel

We need to get started with the preparation of putty mixture. We recommend to use a special putty for sealing seams. Also pick up a spatula, suitable for the operation. It should be with a flexible blade and comfortable handle.

To avoid cracks in the seams of the work should be carried out after the establishment of a constant room temperature and humidity.

The finished mixture with a spatula put on drywall seams, as if pushing it between them, then cut a piece of the desired size of the tape and glue it to the treated joint. Similarly treat the remaining seams and joints. To fill the hole in the drywall screws from the need to apply putty stand into place, smoothing it in different directions. After carrying out all the necessary processes, you can at will prepare trimmed with plasterboard wall for further work. Finishing options can be mass, it all depends on your desires, fantasies and opportunities.

How to sheathe the walls of plasterboard with their hands (video)

Practice shows that if you stick to certain rules and technologies in skin plasterboard wooden walls, the work does not take much time and will not be difficult. In addition, carrying out the installation of drywall in lumber house on a wooden frame with your hands, you essentially save the family budget.

Interior decoration of wooden houses plasterboard (photo process)

Is it possible to fix the drywall to wooden bars: 7 secrets of good attachment 1 2c7f2e47d11e54bdc697dc216142c2f3 12-05-87127871 7a8621cd79aa56640db0783c61138290 000077 188drywall 19337-537409-101 6997272 5213246

Комментарии

Leave a Reply

Your email address will not be published. Required fields are marked *

− 1 = 7

map