The Blog



Transform the bathroom and make it comfortable, you can use the plasterboard boxesTransform the bathroom and make it comfortable, you can use the gypsum korobaOchen frequent repairs in the bathroom and the toilet is carried out in order to make an image of the room more attractive. Availability of communications at times spoils even the most fashionable and stylish renovation. Hide unsightly communication will wash basket made of plasterboard. Box in the bathroom plasterboard with doors and without them you can do with your hands. To do this, you must first read the instructions, after which you can start the repair work. For the manufacture of boxes is best suited moisture resistant drywall.


Mounting boxes made of plasterboard in the bathroom: a preparatory stage

Box of drywall will not only hide the communication, but also to provide them with protection against unexpected mechanical rooms. This material allows us to produce a convenient design, which provide free access to the tubes at the desired moment. That repairs were successful, you need to thoroughly prepare for it.

A well-chosen tools - the key to successfully completing the repair. To work need: a hammer, tape measure, pencil, level, plumb, a knife.

A properly installed duct of drywall will cover all communications in the bathroomA properly installed duct of drywall will cover all communications in the bathroom

The first step should be to draw a master layout, which will determine the frame size. It is important to note that the profile should not touch the pipes. It is necessary to make allowances for stripe sheets of drywall.

How to make the markup:


  • Determine the top cue point, given the floor drawing.
  • Run straight line from the top mark to its very foundations.

The correctness of marking the success of the entire construction. In order to perform layout clearly and precisely, it is necessary to use a plumb and level. After preparatory work, you can begin building and installing the frame.

How to make a box of drywall in the bathroom: the installation frame

Before you assemble the frame, it is necessary to select the material for the profile. It is best to use aluminum. This material is ideally combined with plasterboard, and also has anti-corrosion qualities.

The use of wooden boards when installing the frame will do the job silent and will create additional fastening.

Before installing the box, you should first mount the frame of metal profilesBefore installing the box, you should first mount the frame of metal profiles



It is important to use a sufficient number of beams, which is determined depending on the height profiles. Profile bars prevent deformation under the weight of the drywall sheets. Particular attention is given to the process it is important to cut drywall sheets.

Stages:

  • Cut two sidewalls.
  • Install the side panels.
  • Cut a third panel.
  • Apply the latest bar at the top of the side plates.

When fastening screws it is important to pay attention to what they need to be embedded in the profile. One should not touch the end of sidewall. Do not forget that in the box you need to cut holes that will provide access to communications.

Cladding sheets and how to make a box of drywall in the bathroom:

for covering elements of the frame must be solid. The edges of the side panels must comply with the profiles frame. The last part is to close the side panels.

When attaching elements important to perform measurements and take into account the margins between the screws, which must not exceed 2.5 cm.

Sheathe the bathroom plasterboard can be independently, the main thing - to pick up high-quality materials for construction and perform the installation correctlySheathe the bathroom plasterboard can be independently, the main thing - to pick up high-quality materials for construction and perform the installation correctly

Designated control of serviceability of the pipeline is also made of sheets of drywall. For their fastening use special magnets. The box can be made entirely collapsible.

Variants of decorative finishes:


  • Ceramic tile;
  • Paint;
  • Decorative plaster.

After installing the boxes bathroom will look much more attractive. Noise from the tubes with a much reduced. It is important to make sure that the box does not interfere with the maintenance of pipes.

Technological holes: how to close the pipe in the bathroom plasterboard:

In the formation of the box it is important to leave accessible counters, faucets, valves, reducers and expansion joints. The holes in the material you need to cut large size of the doors themselves. The door frame is fixed after installation.

In order to monitor the sewage hole must be placed in front of the box.

Stylishly hide communication in the bathroom, you can use the plasterboard boxes and beautiful decorative small doorsStylishly hide communication in the bathroom, you can use the plasterboard boxes and beautiful decorative small doors

The door can be placed laterally if it would provide for adjusting the states of valves and pipes. The holes for pipes in the duct should be made slightly larger. The space between them is filled with foam or polyethylene tow.


The components of the door:

  • Frame;
  • gypsum plasterboard;
  • Pressure lock;
  • seal;
  • Door.

For the manufacture of doors and boxes of used water-resistant drywall. He treated impregnated, stable moist air. Gypsum plasterboard prevents the appearance of mold and mildew. After installing the box better oblitsevat ceramic tiles. Then the bathroom will look stylish, the pipe will be protected from mechanical damage, and a box - from moisture. Bathroom needs a special finish that will not deteriorate from exposure to moisture and temperature drop.

Make a box in the bathroom plasterboard (video)

Bathroom full of pipes, which have a negative impact on the appearance of the premises. This is why they are closing duct. It can be made from the materials of various kinds. One such material is drywall. It is better if it is moisture-resistant. To make a box you can own, pre-read the instructions and make a layout. It is important not to forget to leave the inspection doors in the box, in order to be able to continued access to communications in case of breakage.

Leave a Comment

Your email address will not be published.

+ 65 = 71